Home » Cryptos » Installing a Pfister 1-Handle Pull-down Kitchen Faucet – Wheaton Collection Installing a 1-handle pull-down kitchen faucet with integrated supply lines. For this demo we’re using the Pfister Wheaton faucet. But please visit our website to …Sign Up for Our Free Newsletters Did you mean ?I have to be honest. I hate the Price Pfister Genesis faucet in my kitchen. The detachable sprayer hand nozzle has broken off in my hand twice. Then last week I noticed a pool of water on the kitchen counter. I thought one of our Brita pitchers was leaking, so I cleaned up the water and didn’t think twice about it.A few hours later the water was back again. on alert and sure enough, the damn faucet was leaking.I called a plumber out and he offered to replace the sink: for about $400. “That includes labor,” he said, as if that made it much better.I put in a call to Price Pfister to request replacement parts. I was hoping that the plastic cartridge that controls the water flow was to blame.

Luckily Price Pfister has a lifetime warranty and they sent the parts out free of charge. Not so luckily, the faucet went from slow leak to “holy crap” less than 24 hours later. duct-taped a plastic bag around the base to funnel the leaking water into the sink basin. We turned the water on underneath the sink when we needed it, but otherwise left the water off until the spare parts arrived.Only one of the three replacement parts came with any instructions, but there were no overall instructions on how to replace the cartridge on the Genesis faucet. Here’s what I did. What You’ll NeedPhilips head screw driverFlat head screw driver or knifeChannel locks or similar squeezy-tool thingyPrice Pfister part #941-7110, #950-0130, #950-0160, #974-5050InstructionsTake the Price Pfister label off. There’s a screw behind the little Price Pfister name plate. Pry it off with a flat blade screwdriver or perhaps a knife.Unscrew the faucet handle. You’ll need a philips head screw driver.Take the faucet handle off and unscrew the metal fascia.

Use the channel locks to unscrew the existing plastic cartridge retaining nut. I was nervous about deforming the plastic too much, but don’t worry about it. You’ll use the brass piece when reassembling your faucet and you can just throw this away. Did your faucet leak all over your wood floor like mine? In that case, squeeze the shit out of the plastic nut in revenge.Remove the old cartridge. Mine was completely chewed up. There were little plastic shavings all over the base of the cartridge, and a large amount spilled onto the sink.Put the larger rubber washer around the base of the brass cartridge housing. My faucet didn’t have this part originally.Gently push the washer into the base of the faucet. Don’t push the washer in too far. You want the washer to be flat.Put the new cartridge in. It’s keyed to only go in one direction.Screw the brass retaining nut on. Tighten it with your hand, then do another half turn with the channel locks.Put the smaller rubber washer around the top of the retaining nut.

This one goes on more easily than the larger washer.Screw the metal fascia back on.Don’t over-tighten this, as the plastic lever of the cartridge is already prone to wear and tear as evidenced by my old one.Put the Price Pfister name plate back on. No one will know except you. However you might need your memory jogged when you have your next problem with your Price Pfister faucet.Laptop Ddr2 Ram Price In PakistanNotice the new washer, which wasn’t there before.Bmw X3 Window Tint CostParts ComparisonOne thing I noticed was that the replacement parts Price Pfister sent me seemed to be more durable than the originals. Japanese Chin Puppies For Sale Las VegasThe retaining nut washer was originally a thin sheet of plastic. Now it’s a more formidable feeling rubber.

The biggest difference is in the cartridge retaining nut. The original one was a soft plastic. The newer version is brass.ConclusionSo far, so good. Not even a drop about three hours later. I’m going to turn the water off over night just in case. With a Price Pfister faucet, every day is an adventure. Related posts: Tags: faucet, home improvement, price pfister, sinkFAUCETS are valves for controlling water. There are four basic faucet designs: compression, ball-type, cartridge and disk. When any faucet starts to drip, the problem is usually a worn seal or component. Fortunately, these parts are readily available and replacing them is simple. You can usually identify a faucet by its body configuration. Knowing the manufacturer can also help. Compression faucets usually have two handles, one for hot, the other for cold water. They have washers that wear quickly and often require replacement. (Repairing compression faucets was covered in the Home Clinic, June 4, 1995) Ball-type, cartridge and disk faucets are washerless;

they usually require less maintenance. Ball-type faucets have a single handle mounted on a rounded cap. Delta or Peerless are leading ball-type faucet manufacturers. Cartridge faucets have cylindrical bodies and are available in single-handle or double-handle models. If your faucet was made by Aqualine, Moen, Price Pfister or Valley, it is probably a cartridge faucet. Disk faucets have cylindrical bodies and a single handle. American Standard and Reliant are popular disk-faucet brands. Before starting any repair, turn off the water by closing the shutoff valves under the sink. Open the faucet so that the water drains out. It's a good idea to cover the drain in case you drop any small parts. Next, remove the faucet handle. Some handles are mounted on the body with a setscrew. Loosen it with an Allen wrench, then lift off the handle. Other handles are held in place with a screw through the top of the handle. The screw may be concealed under a decorative medallion or plastic cap.

Pry the cap off with a screwdriver then remove the screw. Ball-type faucets control water flow with a hollow ball. Moving the handle rotates the ball over water supply ports and allows water to flow. The ports are fitted with neoprene valve seats that hug the ball and keep water from leaking. Positioned on top of the ball are a cam washer and a cam. The cam washer creates a water-tight seal above the ball; the cam helps to align the ball with the ports. The entire assembly is held in place by the rounded cap. If your ball-type faucet leaks, try tightening the cap with a pair of channel-type pliers. Tape the plier jaws with masking tape so they will not mar the cap finish. If the faucet still drips, the valve seats or the cam washer are probably worn and should be replaced. In rare instances, the ball may be damaged and need to be replaced. Manufacturers offer different repair kits that contain the parts needed to fix the faucet. A complete kit should include a new cam, cam washer, two valve seats, seat springs and an instruction sheet showing the correct replacement procedures.

Depending upon the faucet, the kit may also include a small tool to help remove an adjusting ring in the cap (not present in all faucets). Remove the rounded cap by unscrewing it with the channel pliers. Lift off the cam and the cam washer, then lift out the rotating ball. Examine the ball carefully for signs of excessive wear. If the ball is damaged or worn, replace it. Replacement balls are available in plastic or metal. The metal ones are more expensive, but are more durable. Remove the neoprene valve seats and springs by prying them loose with a screwdriver. Install the new springs and valve seats; replace the ball, the cam washer and cam. Many cams have a small tab that fits into a notch on the faucet body. This insures that the cam will be properly positioned in the faucet. Screw the rounded cap on the faucet, then replace the handle. Cartridge faucets have a rotating valve cylinder -- the cartridge -- that aligns with the water supply ports to control the flow of water.

When the faucet leaks, it means that the cartridge is worn and needs to be replaced. To replace the cartridge, first remove the handle. The cartridge may be held in place with a threaded ring or a retainer clip. You can remove a retaining ring by unscrewing it with a pair of channel-type pliers. To remove a retainer clip, pry it loose with a common tip screwdriver. Remove the cartridge by gripping the cartridge stem and pulling it straight up. Cartridges come in many styles, so be sure to bring the old cartridge with you when buying the replacement. Push the replacement into the faucet, being careful to match any alignment tabs with their respective notches. Replace the retaining ring or clip, then reattach the handle. The valve mechanism in a disk faucet consists of two ceramic disks that rotate over supply ports to control the flow of water. If the faucet leaks, it usually means that the ports or seals need to be cleaned (sometimes the disk may have to be replaced). Disassemble the faucet by removing the handle, then the retaining cap (it may be held in place by a setscrew or screw threads).